On the command prompt of the Admin PC, open a SSH session to the switch using the command ssh -l admin 10.0.0.1 Move on and try to access the switch remotely from the PC.Ĩ. That’s all for SSH configuration on the switch. Now connect to the VTY lines of the switch and configure SSH on the lines.
CISCO SWITCH ENABLE SSH PASSWORD
SW1(config)#username admin password adminĦ. Set username and password for local login. SW1(config)#enable password adminĪgain, note that enable password is not necessarily used in configuring SSH it will allow the admin to access the privileged executive mode of the switch once a remote connection to the switch via SSH is established.ĥ. SW1(config)#crypto key generate rsaĤ.Set an enable password. Now generate encryption keys for securing the session. Configure IP domain name SW1(config)#ip domain name adminīoth the host name and domain name will be used in the process of generating encryption keys.ģ. Now, to configure SSH on the multilayer switch, here are the steps.ġ.Configure hostname Switch(config)#hostname SW1Ģ.
CISCO SWITCH ENABLE SSH PC
Give the ADMIN PC IP address 10.0.0.10 /8 On the switch, we’ll assign an IP address to a VLAN interface, just as we’ve said. Then configure basic IP addressing on the PC and the switch. Begin by creating the network topology.The commands remain almost the same as for the router only that in a switch, we’ll use the IP address of its VLAN interface to access it from the PC.
![cisco switch enable ssh cisco switch enable ssh](https://www.techrepublic.com/a/hub/i/2008/01/16/5f568dd6-c3ba-11e2-bc00-02911874f8c8/remote_commands_cisco_rsh-1.png)
Here, we’ll configure SSH on a multi-layer switch. You can proceed and do configurations on the Router.You’re now managing the router remotely from the PC.Īt this point, let’s move on and configure SSH on a switch. Provide the enable password (the one you set in step 4) to access the privileged executive mode. You’re now probably in the CLI of the router. Provide the login password which you set in step 5 and press enter. On the command prompt of the PC, open a SSH session to the remote router by typing the command: ssh -l admin 10.0.0.1ĩ. Move on to see if you can access the router remotely from the PC.Ĩ. MyRouter(config-line)#transport input ssh myRouter(config)#ip ssh version 2ħ.Now connect to VTY lines of the Router and configure the SSH protocol.
![cisco switch enable ssh cisco switch enable ssh](https://www.cisco.com/c/dam/en/us/support/docs/smb/switches/cisco-small-business-200-series-smart-switches/images/ijgm-083016-ssh-user-authentication-step1a.png)
The password will have to be provided before you can access the CLI of the router when using SSH.Ħ.Specify the SSH version to use. myRouter(config)#username admin password admin ĥ.Set username and password for local login.
![cisco switch enable ssh cisco switch enable ssh](http://lh4.ggpht.com/-p4CJJsezMy0/UMWMzz9b0oI/AAAAAAAACh8/9v32l5h7FRw/2_thumb2.png)
Note that this password is not for use with SSH its only for use in accessing the privileged executive mode of the router after you are able to access its CLI remotely via SSH. % Generating 1024 bit RSA keys, keys will be non-exportable.Ĥ. Choosing a key modulus greater than 512 may take The name for the keys will be: myRouter.adminĬhoose the size of the key modulus in the range of 360 to 2048 for your Now generate encryption keys for securing the session using the command crypto key generate rsa. Set domain name myRouter(config)#ip domain name adminīoth the hostname and domain name will be used in the process of generating encryption keys.ģ. Set Router’s hostname Router(config)#hostname myRouterĢ. Now, to set up SSH on the router, you’ll need to:ġ. Then do these basic IP configurations on the PC and the router: Once the connection has been established, a network admin can execute commands on the remote device.Ĭonfiguring SSH on a router in Packet Tracerįor this tutorial, we’ll configure SSH on the router so that you as the admin can access and manage it remotely using an SSH client on the admin PC. The client machine (such as a PC) establishes a connection to a SSH server running on a remote device (such as a router). SSH is a client-server protocol, with a SSH client and a SSH server.
![cisco switch enable ssh cisco switch enable ssh](https://www.cisco.com/c/dam/en/us/support/docs/security-vpn/secure-shell-ssh/4145-ssh-5.gif)
However, with SSH, all data transmitted over a network (including usernames and passwords) is encrypted and secure from eavesdropping. Secure Shell, just like Telnet, enables a user to access a remote device and manage it remotely.
CISCO SWITCH ENABLE SSH HOW TO
Welcome to this tutorial! Here, we’ll have an overview of Secure Shell ( SSH) protocol, then see how to configure it on a switch and a router in Packet Tracer.